Exactly How To Install A Bath Tub (For Novices).
Exactly How To Install A Bath Tub (For Novices).
Blog Article
The content following next on the subject of How to Install a Bathtub Yourself is relatively engaging. Read it yourself and decide what you think about it.
Installing a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably hard project. If the old tub is readily easily accessible, the task can move immediately; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also set in the new one. Ensure you have actually certified on your own for the work and also are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is better to consider employing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This short article will help you install a brand-new bath tub in your washroom if you have actually already purchased a new tub and also don't require to transform the setup of your previous water system pipelines.
Your tools and material list must make up the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome because of the restricted access that is usually the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a towel prepared for the remaining water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Secure the faucet in place with the maker provided backnut. As soon as the tap is safely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind ought to be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are practical in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Activate the water and check all joints and new pipework for leaks and tighten them if required. Fill up the tub as well as likewise check the overflow outlet and the normal outlet for leaks.
Finally, repair the bath paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last position.
Preparing for the Installation
To start with, the sustaining structure provided with the bath should be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a rigid seal, creating the water to permeate the wall in between the bath and the tiling, bring about problems with dampness and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are sold in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill up the bath tub with water before securing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I found that blog posting about How to Install a Bathtub while looking around the internet. Sharing is caring. Helping people is fun. We truly appreciate reading our article about How to Install a Bathtub.
Click Here Report this page